The Grip Clip tarp and tent fastener has many automotive uses. With Grip Clips and some tarp, you can create a waterproof, windproof cover for your car, truck, motorcycle, boat or RV. Grip Clips won’t puncture or tear tarps and won’t “pop” off. Grip Clips are quick and easy to install.
Since the Grip Clip vehicle cover is formfitted by you to fit your car truck or RV with Grip Clips, it won’t flap around as much in the wind and you won’t have to anchor it. You can create a snug fit in several ways. Gather the tarp in various places around the entire base and secure each gather or fold with a Grip Clip. For a easy-to-remove cover, make the gathers less snug. And on one end of the car, attach a cord or bungee cord to 2 Grip Clips which are several feet apart. Cinch and knot the cord to get a secure fit. Just untie the cord to take off the car cover! Click on a link below to see some examples.
Cover Truck Bed With Grip Clips
Keep some Grip Clips tarp fasteners, cord, and a tarp in your truck and you can cover your truck bed securely and quickly anytime. A perfect solution for dump runs, hauling yard waste, or keeping rain out of your truck bed. Grip Clips won’t puncture or tear tarps and won’t “pop” off. Grip Clips are quick and easy to install.
Grip Clips are well suited to creating truck bed coverings for several reasons. Both truck beds and the loads we put in them vary in size. The anchor sites can be either inside the truck bed or outside it. So, it’s difficult to anchor the tarp securely using the grommets on a tarp. Grip Clips can be attached exactly where they’re needed to tie the tarp on snugly–each load you haul. And because of the Grip Clip’s special design, they won’t “pop” off while you’re driving down the freeway.
To make a truck bed cover, we recommend using either our General Purpose Grip Clip (for a regular blue tarp) or the Heavy-Duty Grip Clip (for a thick tarp).
Car Covers With Grip Clips
With Grip Clips and a tarp you can easily create a waterproof, windproof covering for your car, boat, or RV. Grip Clips won’t puncture or tear tarps and won’t “pop” off. Grip Clips are quick and easy to install.
Since the Grip Clip car cover is formfitted, it won’t flap around as much in the wind and you won’t have to anchor it. You can create a snug fit in several ways. Gather the tarp in various places around the entire base and secure each gather or fold with a Grip Clip. For a easy-to-remove cover, make the gathers less snug. And on one end of the car, attach a cord or bungee cord to 2 Grip Clips which are several feet apart. Cinch and knot the cord to get a secure fit. Just untie the cord to take off the car cover! Be careful of moisture build up under tarps and of wind wear on your car where the tarp might rub.
To create a car cover, we recommend using the General Purpose Grip Clips.
Car Seat Covers With Grip Clips
With a few Grip Clips fabric and tarp fasteners, some cord, and fabric you can easily create seat covers for your automobile to protect or further prevent further detioration of the car seat. You simply attach the Grip Clips to your chosen fabric, connect the Grip Clips with cord, and tighten. One benefit of using the Grip Clips in this situation is you can attach them on the fabric where needed to get a snug, wrinkleless fit and you can also control the tightness of the cover. Plus no sewing is required!
Grip Clips won’t puncture or tear fabric or tarp. And Grip Clips won’t “pop” off.
To create a car seat cover, we recommend using our Light-Fabric Grip Clip for thin fabric and the General Purpose Grip Clip for thicker fabric.
Motorcycle Covers With Grip Clips
Protect your motorcycle during the winter months by creating a waterproof covering using Grip Clips tarp fasteners and a tarp. Grip Clips won’t puncture or tear tarps and won’t “pop” off. Grip Clips are quick and easy to install.
You can create a snug-fitting Grip Clip motorcycle cover by gathering the tarp in various places near the base of the tarp and securing each gather or fold with a Grip Clip. Since a motorcycle is tall in proportion to its size and since the Grip Clip motorcycle cover is formfitted and has a small surface area, the cover won’t blow off or flap around in the wind. If you live in a particularly windy place, you might fasten the cover to the motorcycle with an “S” hook or connect two Grip Clips with a bungee cord under the motorcycle.
To create a motorcycle cover, we recommend using our General Purpose Grip Clip.